Phoenix-Brian Priester: Thanks for the advice!
Wish there was a chart for gauges to wraps as a guide. My first dual coil
build on an IGO-W came to .6 and my SVD wouldn't fire it. Perfect micro
coil, but what was the real problem, I was given a length of Kanthal
without asking what gauge... Free is free.
Shawn Elliott: I love your intro! wow
harold buns: Lol i feel like an idiot, i never knew that you could put dual coils on a 2
post RDA. gonna start building dualies as soon as i drill out a second hole
Arturo Mercado: Hi, I bought a soldering iron and it stop heating up. I then open the
soldering iron and one of the soldering iron heating element wire was
broken. I want to know if I could joint a piece of Nichrome Resistance Wire
so that it could work again, or can you tell me how to mend it. I bought
this soldering iron like two weeks ago but I lost the receipt.
Biosystem Studios: I have a LD Igo-W and it has the negative post in the middle so if I'm
getting this right then that should be the only one that has 2 wires
running through it right? The outer positive posts should each have one for
Keith Joshua Balayan: Sir can I dual coil a two pole atomizer and do you think my sigelei zmax
will be able to handle it? Thank you so much sir and more power to you.
JamieD262: what i would recommend to all newcomers and well everyone is to use an ohms
meter (£15 online, lasts years, most VV/VW mods have one built in) before
you attempt to fire up a new build, diving into RBA's is something advanced
users should do, definatly when using a mech mod, ensure you have a High
Drain/high Amp battery if youre sub ohming too.
Tim Quesada: Thank you for the advice M.C. Vapes.
Kristi Wilson: I have a nimbus with three posts. Mine hits great for about a minute then
nothing. I have several different batteries. My coils are very nice too.
Peter Polizzo: send me one of those =)
Alex Martinez: can i build this on a AW IMR 18650 3.7v 1600mAh on a stillare clone?
John Le: @M.C. Vapes Is it bad if the wire that goes through the middle post
touches the coil on the other side? Mine is micro coil dual build. But the
wire that goes through the middle post is extremely close to the coil on
the other side.
vincenzo formosa: What voltage battery would you recommend for a mechanical mod with a dual
coil. Looking at .5-1 ohms? Does it matter?
Tim Quesada: How do you avoid a short on RDA's ?
Jay hernan: Thanks for the video! Just subscribed. Just bought the hammer mod with the
Patriot clone. But no wick or coils.. You think cotton is better that
silica? Also.. Why are there other people that do like 7 wraps and torch
Courtney D: those are some crapty ass punto lunto ass coils
Justen Annuar: thank you very much
macker33: would look good on a black tesla
Jason Adams: Here's an idea unless you already tried it, how about a quad coil on a
amir benglisa: i just bought a kamry k100 what do you think i have to do to make big
clouds? should i use the cartomizer that comes with it?
CashRockThunderMamal: I do not like this RDA at all. So glad I got an Omega.
Sveinn1984: Great video, thanks for the tips!
Ethereous: Holy freak, that stupid, long-ass intro that no one gives a freak about.
Richard Michael: You would DO WELL to use an OHM Checker.... every time.
Zori Marfazelian: how do u know when u need to redrip as in how do u know u burned through
your juice so u can refill it???
ZeRo2o9: what do you reccomend on wire & wick for the nimbus? Im a beginner trying
to learn I just want to change the wicj that it came with
Jose Allan Goco: How about 4 wraps of 20mm Kanthal just to be on the safer side, will that
produce as good a vapor?
Carlos M: Whats up MC vapes! I am using an aspire by nova with a dual coil and i also
just got the aero dual coil by kanger tech. I wanted to rebuild the
atomizers and came across your video. I on the aspire they have negitive
resistance on the end of the coil wires. Is that needed for the aero kanger
dual coil ? If not why is that ? Thanks
liza dickson: nice vid but what about the risk of over working your battery and causing
thermal meltdown..vent gas or BOOM! ?? er.. the c rating of your battery
is? how many amps does that setup use? If people burn themselves multi
coiling, this could be used againt us.
cameron telford: So im planning on picking up the stellare RDA today which has 3 posts and
going for my dual coil build this afternoon my biggest question and consern
is shorts I have done alot of reading on it and cant find any information
on what causes shorts. Please help haha
Tommy McFarlin: Great vid. Ready to start building my own!
Bob Starr: Glass does not bio-degrade in your lungs. Your going to get black lungs.
Tim Quesada: BTW, thanks for sharing. I'm a newbie on dual re-coiling.
Blaine Carter: can i pay u to make me one
Eli Carrillo: Hi,
I just liked and subscribed!!!
I wanted to know what do you use to measure the resistance of your coils
before you vape..
And also where did you buy it???
Bob Starr: You had my interest up until you started smoking the silica into your
Tony Reynolds: Great video...just liked and subscribed ! Thanks for sharing ! !
nathan mccully: thank you your video helped me to do my first successful build I did a 3
coil rap for each coil with double silica wic once again thank you
Dustin Frisbie: Thanks for the tutorial, i been attempting my first dual coil build and for
the life of me could not figure out why I was not getting the good hits and
clouds as I was with my single coil.
Ben Pena: Thanks for the tutorial bro.
Anthony Carrillo: Biggest help iv had thus far thank you
hquiroz113064: dot worry about uncle bob there he is just pissed about nothing!
Kool Yoo: Oh, and one more question, the coil needs to light up evenly right? what if
some is slower to light up and some are fast? Many people tell me to fix
the coil. But how do we fix the coil? I already separate each of every coil
evenly, but still the whole coil does not light up at the same time. Some
slow some fast. Sorry about my english, hope you understand my question =)
MissKarizma: Thanks for the tutorial, gonna try this tomorrow :)
Andy B: I have a question for you M.C. Vapes
I have recently entered the world of RDAs, and made my first set of
dual-coils on a chinese knock-off Nimbus clone, which worked perfectly. I
ran into a problem where when I used 28g Kanthal A1, by the time you
twisted the filament wire up (to get more surface area), the diameter of
the two coils together into the centre post was too large to pass through
the hole in the post. To alleviate this I can drill them out, but if I go
too large I run the risk of drilling the threads clean off .. I've already
ruined one by going up to 1.5mm, it was the only drill I could get, but I
was thinking if I went up to 1mm-1.2mm it should be ok.
My question is .. do the genuine Nimbus RDAs have larger holes (larger than
1/4"), and larger screws ? Have you run into this problem already ?
knz9701: I'm a NEWBIE to wrapping coils.. I don't understand the whole bits tool
yet, though I'll be more excited about it laters… Thanks for making this
video, I did a trial run and my wraps were too lose.. Than I did exactly
what you did in the video and this one works for me, one side came out
perfect and I had to tweak the other side but for a 2nd time wrapping it
being a newbie I'm pleased with it.. I really appreciated this, mahaloz
from the "Big 808"!
Kool Yoo: 1) If building dual coil, can both of the wire touching each other on the
same pole/post? or we must separate them? e.g. (one wire we pull to the
left, and the other one to the right.)
2) Can the coil touch the pole/post?
I need the answer.
p.s: sorry about the bad English
Kevblaze15: hey man im having problem with build i use a zmax battery and i cannot get
my build to read over 1.2 ohms witch is the lowest that my battery will
read i am using 8 wraps of 28 gauge wire i even tried going up to 10 wraps
and still cant get it any help would be nice.
Bob Starr: I thought that this was a coil winding trick to generate Free Energy...
Build: Dual Coils & What You Need to Know4.6
out of 5