ZERO TURN MOWER REPAIR How To Replace The Pumps And Wheel Motors




What do you think about this video?

Dave Nolan: I've got a cub zero and the left side is weak . Can you buy a rebuild kit for the hyd pump and kit for the wheel motor ? I'd like to rebuild the pump and wheel motor since the pump is $450 THANKZ 

twenty2eight: What does it mean if the whole left side of my Gravely won't move?

Frankie Ybarra: Jeremy, trying to put the drive belt back on a Gravely 152Z hydro turn mower. What's the trick to treading it through? It seems to small to fit. Thanks! Frankie

Ed Dembowski: Hey Jeremy... just recently acquired a Woods R2048 zero turn that seems to run well (motor on it at least) but has it's share of problems. First of all doesn't have much power going forward (left side has more than right), I can go back and forth to gain power and will eventually go okay on level ground but must do most inclines in reverse. Someone replaced the original motor with a 14.5 hp and I'm wondering if that would be giving me the issues I'm having that seem like hydro problems? I think I will start with changing fluid and filters because I don't know if they've been changed or not, making sure no leaks anywhere and purging system of air. Any other suggestions???

kevin wagner: i have a lesco zero turn rebuilt pump ive tried to purge system cant get fluid out of the high side of pump tank full and filter is also should i fill the pump up first and try or do you have any ideas 

Yolanda Hacker: HI Jeremy. Time to change Hydro trans fluid. 500hrs Simply drain tank and replace filter? What about remaining oil in motors and lines? I have the same Gravely you repaired in your video.

Lisa Beebe-Strahley: I have a Gravely 260z and have replaced the Hubs and can not get the hub all the way up on the spindle to seat, stops short of the cotter pin hole by 1/8" or 3/16", the hub nut goes on with a couple of treads showing. Had to use a car hub puller to get the old one off. I did grease the spindle shaft before installing the new one and did align the keyway. Any thoughts

John Guzman: jeremy seeing if you can help, I have a swisher ZMax ZT2660 with eston transmission system. I put regular hydrolic oil 32W in the reservors and now it starting to drag. any suggestions on how to fix problem. did i use the wrong oil. what type of oil should i use in this eston transmissions. your insight would be deeply appreciated, thanks, John

David Smith: This must have been one expensive repair bill. 

2LateIWon: Nice job I'll be replacing the motor (just ordered it should be here in a few days) On my Toro Z420

Lanetta Walley: Where do you get the parts from... im looking for a gasket set for the hydro wheel drive 

73 SUPERGLIDE: I hear the piston are aluminum ba:cause wear out because fluid not maintain

natureboy6000: i have a woods 6160 0 turn mower,one of my hydros stop pulling,when i push or pull the level it just whine and it act as if it wants to move backward or forward.if i turn it off for about 10 mins or more and start it up it will go about 5 yds until it stops again.if i push or pull the throttle on that same hydo the fan slows down or stops until i put the throttle back in the neutral position..Can anyone please help me this?Thk you in advance

kenneth atkinson: how do you purge it where is the purge valve 

Nicholas Cooper: Great video Thanks

73 SUPERGLIDE: Wood u not what flush tank and hoses be for new parts

Bill Bassett: Hi Jeremy. I have a Bunton zero turn that is chattering on the left side. The unit is still pulling and has good power but is weaker than the other side. My question is how do determine if it is the pump or the wheel motor? Thanks for your time. I think it is the wheel motor but not sure.

Jay Birdi: How many hours until you need to change the hydro oil?

Phil Dugas: I need to adjust my gravely zt hd 60 it pulls to the left any suggestions where I could find out how to do this? thanks for your time 

Mike Abrams: My Z152 just quit moving today and the hydraulic lift wont move either. Do I need to replace the pumps?

Dennis Loch: Good Video. 

Jeff Willis: Thanks for the video Jeremy. Just picked up this model Gravely with 440 hrs. No signs of pump trouble yet, but have this video when it comes time. How do i tell if my mower currently has hydraulic oil or 20w/50? Is hyd oil much thicker? THanks for the help!

Lorddarthvader1701: Great video, just bought my forst ZTurn, bought a Toro Trim Cutter 42, do you know who makes the wheel motor for them

David Thorne: Where do your old pumps and motors go? I'm looking for sum to deconstruct? Hydraulics is cool...man

Fernando Jurado: Hi Jeremy. My Ferris is1000 21hp 48 inch have similar problem on the left side. Do not go forward. Only go back fine. Do you have any idea what wrong with it.

idlossett: Jeremy, I appreciate the demo on the Gravely pump and motor removal. I have a Farris IS 1500 mower and I used your method to remove the hydraulic motor but ran into problem getting the belt pulley off. Will you please advise me as to how to remove the Farris pulley. My mower is about 4 to 5 years old. Please send your advise to my e-mail address which is IDLossett@gmail.com. I to look forward to your reply!!!! Many thanks

Joseph Bragdon: A bunch, $615 each pump and at least $500 each for the wheel motors. Ouch, thats what I'm looking at right now.

JEREMY FOUNTAIN: we use the manufacture shop issued online manuals

zx8401ztv: I would have thought the owner would have taken 10 mins to look up the correct fluid type, as they are not cheap mowers. Hope you got yourself a nice cool drink, you looked well cooked. Just as good as new, bet the customer was happy as larry with it :-)

knighthawk86855: Hey man great video...quick question for ya...just picked up a free Dixon ztr428 zero turn mower....it works prefect runs strong and cuts perfect too...it has a new 14.5hp Briggs intek engine....my question is...what do you think of these Dixon mowers....any huge problems with em...cause I'm thinking of keep it for myself...never had a zero turn b4...any advice would be awesome...ty!

Fernando Gonzalez: Sure is a lot, still haven't gotten to my mower. Hope to replace mine soon, the price is a lot!

johnnybgood42: G'Day, just w0ndering if you have a Email address,? id like to talk to you about converting my Austwood ZTR 1500 from the failed Eaton hydrostatic 780 Transaxle to pumps and wheel motors , EG: what size pumps? and size motors? do you think id need ? . By the way Great vid !!

JEREMY FOUNTAIN: PURGE THE AIR BY JACKING THE REAR TIRES OFF THE GROUND AND STROKING THE HANDLES BACK AND FORTH TILL YOU SEE NO BUBBLES IN THE RESERVE TANK ( MAY TAKE UP TO 1 HOUR) THEN AFTER THAT LET THE UNIT SIT FOR 24 HOURS

bryce hunter: this is a good video!..

Patrick Moore: What oil do you put in hydro trans axels in garden tractors?

Billy Innes: Had an old bobcat skid steer took 30 engine oil non detergent if I remember, it was a 1979. Don't know why they just don't design these thing to take the red oil to make things easy. I now both engine and tranny oil both have hydraulic in them and tranny is equivalent to a 30 weight oil but don't use it cause of foaming but it does have heavy conditioners in it I've heard of people mixing in a few quarts of tranny fluid with a oil change to clean a motor. Similar to a marvel mystery oil. Man I

Steve Junga: Great video! I have a gravely zt1842. left trans grinds and shakes. Can i rebuild it? if so where can i get a rebuild kit? my friend has a exmarkwalkbehind parts mower with the hydros. will the exmark parts be compatible? Thanks Steve

zyplex1: Great info Jer, that's a lot of work, if I may ask how much labour does a job like this cost the customer asides from all the new parts ???

Jake Hindman: Thanks for the info man. Very good video and information! Lol wish I could've found this before I spent almost 700 dollars on a new wheel motor and labor

grease82monkey: Nice video

lawnside82: wow i learned alot. now imma start looking for zero turns with bad hydraulics. and replace the pumps..

Thomas Baxter: Thanks for the info...

Steve Rob: Fantastic !! That vid was jam packed with info ,too bad it wasn't longer. If you happen to do another hydraulic system ,would like to see how the bleed process is done.

JEREMY FOUNTAIN: ALWAYS GO OEM AS THEY MAKE DIFFERENT CC PUMPS GOOGLE THE NUMBER OFF YOUR PUMP AND ORDER THEM ONLINE OR FROM A REPUTABLE DEALER

ryecard: 2 questions : (1) Is a Dixon 4421 ZTR for $450.00 worth buying ? It's rust free and shows a bit of seepage here and there. The cheap fenders are beat and one light missing but the oil looks fresh and the frame looks in good shape. Question ( 2 ) I got a early 70's FORD LGT 125 I mow with. It squeals like the mower in your vid when ever I drive it but not in neutral. It scoots along just fine but I can't figure out where the noise is coming from.

Kerry Geen: Man could I do with you here for a while, you are one very talented man. you work so quick and efficent. I have spent a day trying to bleed my husqvarna iz4821 and while the oil in the res tank starts off clear it soon becomes milky with tiny air bubbles. everything is tight and I have purged heaps of times. I need a Jeremy! Where can the air be getting in?

Fernando Gonzalez: How much does both pumps and wheel motors cost?

TDHReviews: man that guys putting some good money into that thing

John Jackson: Extremely well presented!

DNA Tech: Love the video! I have a question for you. I lost my drive belt last week at the bottom of my driveway. I opened the bypass valves as best as I could and pushed my ower to the garage. I went ahead and replace both belts (drive/deck) then proceeded to close the bypass valves. The left motor closed but the right valve seems seized! It will not turn either way... I tried raising the mower up like you would to bleed the system and run it for a few minutes under zero load. Bypass still seized. Help

Rating:
ZERO TURN MOWER REPAIR how to replace the pumps and wheel motors 4.7 out of 5

Shared by Others

ZERO TURN MOWER REPAIR      how to replace the pumps and wheel motors
ZERO TURN MOWER REPAIR how to replace the pumps and wheel motors
Fuel Pump Replacement (part #2439316-S) - Kohler Small Engine Repair
Fuel Pump Replacement (part #2439316-S) - Kohler Small Engine Repair
DIY Mower Seat Repair -  Garden Tractor Seat - Zero Turn - eXmark
DIY Mower Seat Repair - Garden Tractor Seat - Zero Turn - eXmark
Zero Turn Mower Spindle Repair Great Dane Chariot
Zero Turn Mower Spindle Repair Great Dane Chariot
Husqvarna RZ5426 Zero Turn Mower Review
Husqvarna RZ5426 Zero Turn Mower Review
Scag Mower Hydro Wheel Motor Disassembly Part 1
Scag Mower Hydro Wheel Motor Disassembly Part 1
Husqvarna RZ-series Zero Turn Mowers: Maintenance
Husqvarna RZ-series Zero Turn Mowers: Maintenance
how to change the blades on a zero turn mower or riding mower
how to change the blades on a zero turn mower or riding mower
GRAVELY ZERO TURN MOWER REPAIR       mower leaves grass behind while cutting
GRAVELY ZERO TURN MOWER REPAIR mower leaves grass behind while cutting
zero turn mower blade change with impact gun
zero turn mower blade change with impact gun
Zero Turn Tractor Hydro Fluid Change
Zero Turn Tractor Hydro Fluid Change
Toro TimeCutter MX 5060 Zero Turn Riding Mower Review...... Independent Review
Toro TimeCutter MX 5060 Zero Turn Riding Mower Review...... Independent Review
How to take blades off zero turn mowers
How to take blades off zero turn mowers
Stator Replacement (part #237878-S) - Kohler Small Engine Repair
Stator Replacement (part #237878-S) - Kohler Small Engine Repair
eXmark Lazer Z Caster Wheel Bearings - Zero Turn
eXmark Lazer Z Caster Wheel Bearings - Zero Turn
Ignition Coil Replacement (part #793353) - Briggs and Stratton Engine Repair
Ignition Coil Replacement (part #793353) - Briggs and Stratton Engine Repair
Hustler Super Z zero turn mower - Part 1
Hustler Super Z zero turn mower - Part 1

Featured Video

How to Make Money Online


ZERO TURN MOWER REPAIR      how to replace the pumps and wheel motors