Chris Henson: hey i changed my ujoints in a 1999 silverado 4x4 standerd cab short bed 1
piece drive shaft i had a sqeek and a minor vibration at around 60 i have
new tires on it with less than 10k miles after changing the 2 ujoints the
vibration changed to a 50mph to 65ish mph at 70 it dose bot really vibrate
it dose vibrate in nutral if i get to speed then coast back down new wheel
bearings 5k miles ago new rotors all the way around at same time the wheel
hub bearings were done im wondering if i didnt put my yoke on the wrong end
as i have done this repair many times and had never had any trouble not
marking my drive shaft any ideas
pr watt: Is there a cross member to support The tranfer case on a 1984 chevy blzer
s10 4x4 I just rebuilt he egine and tran. I don.t see any bolt holes to
support tth tr case. Does it just hang off the tansmission. Seems like alot
Monica Camacho: i have a 2003 chevy silverado 4x4 2500hd and when i put it n reverse i get
a grinding sound does anybody know what could it be and how do i fix it?
mike keller: i tried like 3 times and couldn't fit a snow shoe in the case. do i have to
go to Alaska to get the snow shoe or will a mail order snow shoe work?
i wish they would have been more clear on that!!!
Adam Baber: I wonder if this the same for a 03 Chrysler, I gotta replace the transfer
case in my jeep, would like to keep the new one lasting longer
Brittney Kuljis: OK I just rebilt a 213 transfercase it is in a 1995 Dodge Dakota. The
problem is it seems to be stuck in 4 wheel drive. Do you have any idea what
would cause this to happen
Carl Zorro: I had my transfer case and rear differential worked on, took it back 2
times and now I get a rough humming sound, thinking it could be from wheel
alignment and knowing I had a tie rod going I changed all hub
bearings,complete tie rods,rotors and pads. Coming back from alignment I
get smoke coming out from the passenger side but not from brakes. This
humming sounded beside a whining like when is the power steering pump but
it's not, can it be from the transfer case, already been back to the shop
qwerty12345470: Wow, good engineering GM. One reason why I'll never buy one of their cars.
This isn't the first time GM has made a crap product.
Carl Zorro: had taken it back 2 times for the transfer case
herbienbrian2: The built big block in my pops K5 blazer blew one of these crapty chain
driven transfer cases to smithereens. (check out the vid on my channel if
you don't believe me)
Time for a gear driven set up.
Henry Veitenhans: Is it a big job to take out the transfercase to do this? I need to do this
on my duramax
Carl Zorro: Getting a clunk as I speed up But is nothing to do with tires,brakes hubs
Tommy Bowen: Does the front shaft turn when you turn rear shaft even if it's not lock in
four wheel drive? Some people say it does and some say it's not working
properly! This is in a 1999 chevy
Anthony Cinquegrana: I think I have this problem with my truck.. I have an 04 sierra. When I
stop and then take off there is a bang from first to second. I can also
feel the bang when it shifts down. I diagnosed the sound coming from the
case.. maybe the chain Is stretched? It "seems" loose, not sure.
kenman1717: I'm a mechanic and worked at a chevy dealer for a long time, fixed lots of
these, replaced a lot of transfer cases because it was to late, but if we
caught it early, just the rear case half could be replaced as well as the
update, that little anti rattle clip on the case is removed and a new wide
one that fit over the pump and wrapped around that edge, problem fixed, no
need to get that aftermarket pump, with that block at the end, because
basically the updated piece from GM becomes that block.
kirk dustin: My 1977 Chevy C 30 Deluxe 1ton flatbed has new clutch, universal, brakes,
just completely tuned-up & has run great since 350 rebuild was installed 10
years back. It has hauled TONS of roofing materials & firewood successfully
as we also beefed up the leafs. In the last 90 days or so the truck has
been doing this weird "grabbing & popping" making it difficult to pull away
from traffic signals, etc. even when not loaded. So after bringing in a
load of Oak firewood late yesterday, when we unloaded and tried to move
forward, it would NOT budge. Acts like maybe rear end is locked up or
something. What do ya'll think please?
boinkburger: Not sure if this applies to the problem I am having or if it's the shift
actuator. But I have a 2003 Sierra 1500. When I start out in 2WD, I hear a
distinct clicking sound from the transfer case and it feels way under
powered. But once I get to 10 mph or so it goes away and drives fine. It
feels as if the truck is having problems deciding to be in 2WD or 4WD. Any
H22TRUCK: Just needs a slip yoke eliminator now
hondatrx100: nvg 246 transfer case
hondatrx100: thank u trucku for the infomation and youtube
ali kai: does this apply to the Escalade transfer case as well ? I understand
Escalade uses pretty much the same GM parts as a tahoe.. I want to make
sure before I do any unnecessary work
rasta1228: i am having this problem with my 2003 1500 hd is that bearing for the rear
output shaft pressed on?
MojaveOutlander .: so what if I used jb weld and threw some duct tape over it?
985southernpride: Does anyone know which side the vehicle speed sensor is on these year
models?? Right or left on the back of the transfer case??
night rider king of road: I had changed the trsnsfer case cuz of oil leak by the same reason I need
the part no. And how to buy it. my car is superbun chevy k25 year 2005
86godsmack: @Trinity73160 seriously??if you can't figure that out then you don't need
to turn a wrench.
BoobyMcDoogle: Does this apply to NP233 transfer cases? 96 GMC Sonoma/S10.
hondatrx100: merchant-automotive is were u can get the pump upgrade
imthenoid69: happened to my 02 silverado twice. the first time, the dealership "fixed"
the problem with the same setup for $1700. the 2nd time i took to local 4wd
shop and they fixed it correctly for $950. both times had to replace the
half case. dealership is scum. should be a recall
takeadayofff: Good info, I didn't know about this problem with aluminum NPs. Still, the
better fix is to upgrade to a full-time cast-iron t-case :-)
ibrahim alzogibi: never buy GM 4WD truck :(
josemania81: I have the same problem or idk I need help, my 4x4 v8 k-1500 1991 I place
it into gears and it will only roll one of the 3 wheels what can be the
problem there? Help? They said my
cdawg4391: @420wurtz sounds like you're running an LSD (limited slip differential) in
the rear with an open diff. up front.
ali kai: there is .. search youtube "Nvg 246-Np8" and it will pop up.. I tried to
post the link but youtube wouldn't allow me
BEASTsatisfaction: My transfer case blew...wow
hondatrx100: o ya becarefull of them snap rings there a pain in the azz
shawn slater: i have a 1990 gmc sierra 2500,my cv joint wont stay in the transfer,keeps
popping out what could be wrong
lexi moubray: i have a2006 gmc it wont shift out of 4 low when i took out the actuator
the 4 low light blinks
Tom Lee: My have problem too. F-CKING Government Motors blow goats.
Jman26063: So far JB WELD has held up over 60k on the pin hole formed from this issue
ibrahim alzogibi: i fixed the transfer case many times ( 3 different factory problems).
TONYLOVE1: Great Info thanks...
dmaxallitech: you can buy it online. search merchant automotive
hondatrx100: because its internal and the houseing will break
speck444: hey matt slap that freakin bruno
Gary Seymour: Great video, however nobody has any videos on a complete disassembly and
reassembly of GM 246 transfer case nor can I find any manuals on this type
of transfer case. I can only find partial disassembly video's on any
transfer cases. Sure would great for somebody to make a video on a complete
disassembly and reassembly of a GM NP246 transfer case for us guys who
don't do this for a living.
1990laserdsm: what is the name of the kit? dose oreily's offer it or autozone??
FSJ19791: GM DIDNT DESIGN THE TRANSFER CASE , crapTY ENGINEERS AT NEW PROCESS GEAR
DID , HAD THE SAME PROBLEM WITH MY TRANSFER CASE AND IT BURNED IT UP