How To Set Up DJI Naza Step By Step Video With Transmitter Setup




What do you think about this video?

CJ Browny: Fly-a-way mode is setup from your receiver for the radio. The radio really has NOTHING to do with the RTH (return to home) function other than to talk to the receiver. FrSky sells a receiver and Crystal for the 9X as a easy upgrade.(I use it) Simple to setup and just a push of a button to get RTH going. When your done you can shut off your transmitter and the quad will go into RTH. If you have a Naza simply check off the RTH option in the menu and your quad will record the GPS location after it lifts off the ground and then go back to it after it has a GPS fix. I am in the process of setting up a multiple camera system using 1 gimbal output from the naza for the switching. And I changed a camera out for a less fish eye look...4X lense. Most of the confusion about RTH is people think the radio dertines it-it does not...your reciever does.

Сухомлин Артём: Есть проблема: перестали отвечать кнопки за переключение между ATTI GPS и MANUAL, вероятнее всего когда на симуляторе играл, забыл выбрать другую конфигурацию, теперь не в одном из выбранных не реагирует. Всё делаю как по видео, не помогает(((

Wayne S: Thanks for the great video, sorted most of my questions, I just have to get the toggle 3 way switch set so up is GPS, middle is Atti and bottom is failsafe. then course lock and heading lock on a couple of the 2way switches and I should be all set. Thanks again you are very clear in instructions only the assistant is old version but I followed well enough with the newer version I am using.

OSCAR OSCAR: Hi Kirikset. I´ve followed your tuto ( it´s grate ) because I have the same Turnigy radio but have a problem. When I move the throttle the channel U moves too, so it change the fly mode from GPS to manual to att and so on. You know what happens? Than you

Frosty619: Thanks for making this video. It helped with most of my set up.

erkan aksoylu: spasibo

yogii1958: I'm not sure but I think all this radios are created different depends on geographical location. I think it's a good video. Did teach me more about Turnigy 9X 9ch radio. 

Guide504: hi there I cannot set up the transmitter link loss failsafe on either of my naza m v2's. the turnigy 9x just will not work. I am using standard v2 with v2 module and rx when I turn off the transmitter it just stays in the air until I switch the radio back on and retake control. as far as the 9x failsafe I have tried to use it to activate the failsafe value on the three position switch and this does not work either. any ideas.....I am starting to think of a futaba t8j.........!

James Dyke: Superb video. I was panicking when I saw the 42 page manual, but this video really clears it up. 

3D Editor: does the receiver stay connected to the naza inside the quadcopter once everything is calibrated? Also why did you skip channel 5 on the receiver?

Andrew Tsousis: HI Thanks for the helpful video. I've got an interesting issue which i can't solve. DJI assistant shows me in the TX Cali window that each slider is green, but my sliders do not move at all when moving the sticks.(Also the MC Output is "On" i notice yours isn'y in the video) I did notice that when i power up the Quad that the Versatile Unit, and Receiver power up fine but the ESC's make no noise at all?? I'm using a HK Power distirbution board, and Turnigy 30amp Esc's with Sbecs built in. Any help would be great.

CJ Browny: I have this video in my favorites because it is intelligently presented and clear and to the point. Thanks.

e Nadir: Hello, I followed all the steps :). But my problem that my dji f550, naza-m lite with turnigy 9x mode 2 (v2), my problem that can't start the motor's! ! I'm not sure what is wrong/problem and really need help (please). Many thanks

Laskar: You don't speak about IOC ...

Robots4Sale: everyone says use acro for turnigy 9x and quadcopter, so i need those settings

kalabakacity: The best video for connect turnigy to naza!! Great video.... Bravo from Greece!!!

Dean Sutherland: Hi i have a DJI phantom 1 and i have a turnigy 9x. can i do the same setup like you in this video?

Joseph McWilliams: Thank You Very Much! The video with the remote on the right side and NAZA assistant on the left was brilliant! I had one thing reversed, now everything works great, Kudos on the most excellent video!

Mike Holt: Can I use versatility unit (with USB cable) from Naza MC 2.0 to plug in to NAZA lite MC for programming Naza lite?

Michael Pregger: Hey there. I Know this is an old video but can you help me with this issue? I have the Turnigy T9 Connected to the default receiver and to a Naza-M V2. Now I have set up the flight modes (GPS, Atti, Manual). I am also able to set the Gear-switch as a forced Failsave switch. But I am not able to set an other switch The IOC mdes? I would like to just set the Homelock on an off with a two-way Switch.

jester f: you forgot to show how to set up fly away mode, wait i think thats already set up from factory

فلزات قیمتی: در انتهای خلوت شب تکنولزی و صنعت

Edward Siyavong: I'am having a problem with my naza assistance solfware at thd bottom box that said mc output on or off,my saids on and do I turn it off.? Thanks

Nathan Bowles: I cant get my turnigy 9x to even do the TX calibration, keeps coming up with errors

ThinkGreen1976: Awesome video about Naza setup with Turnigy 9x. Manual does not say lot's of stuff.

rockyFLYR: you are the best!!

TheFido03: Just wanted to add that i can get it to failsafe with the switch like in your vid.

cpenteriche: Hi, thanks for your quick response. I just want to know how to setup my turnigy 9x with home lock or course lock, since I cannot have both configured. It will help a lot for sure since I'm a begginner. :)

Soldier53flyer: Hi I'm having trouble programming my Naza? it will not talk to my quad? can you help me? Please. the software is not working.

TheFido03: On another video it said to set the transmitter on acro and not heli becuase it won't fly correctly.

kirikset: what happens if you take your naza out of the copter, connect it to the VU, power it up with nothing hooked up? Does it flash the light like a normal start up sequence? Try connecting to the pc to check the the light turning green and wheather the naza sees you transmitter input. Also check ESC's and motors by hooking them up to the transmitter directly, calibrating, checking all settings on them and running your motors. could you please share what you've checked and are 100% shure that works?

kirikset: I do not own WKM, it is an overkill for my smaller quadcopter and I really have no complaints or missing features compared to WKM to buy it for my much bigger hexacopter. I do not know anyone personally and have not seen step by step setups. Maybe check DJI youtube channel, they seem to post lots of tips. 9x may be not enought if you want to use all features at the same time and i strongly advise againts using it with stock radio link as it lacks fail-safe. If in no hurry - buy frsky taranis

Mike Flyer: Sorry I spelled your name wrong.1jamac1

Ixtocaltro: Thanks for your fantastic video. Just two question: 1. Why do you set it on heli mode? 2. Is it normal that motors startup very fast? Thanks for your comments.

david ringler: i have the turnigy 9x with stock receiver,will i be able to follow your video and have a failsafe like you have shown?. davidringler40@yahoo.com

Gareth Rens: did you install the USB drivers for the naza???

GarretB123: Thanks much! My F450 Flamewheel with Naza controller is almost complete. I just received my GPS yesterday and I was getting worried about setting it up with my Turnigy 9x (modfied with FrSky module). I'm grateful you put this video together. It is going to help me tremendously!

kirikset: yep) after 7:50 I do almost the same thing. You should experiment with pitch values to see which correspond to what control modes. Then simply choose the desired order of flight modes and set three pitch curves to the corresponding levels.

kirikset: I'll soon get down to making tonst of videos on my current setups. It's been a crazy summer. I've been trying to build, test and fly lots of new models, because from november til may there is basically very little opportunity to fly anything but DLG and big multirotors for me.

rcartelian: Any video with new configuration ? I have same Turnigy 9X v2 , with FrSky D8R rx and DJT mod. and try to figure out withc is the best solution setup. Any difference true the setup from this video and FrSky ?

BENNY THE BRAVE: hey mate i have a spectrum dx8 and I plugged in all the plugs in the right spots and i turn it on and it flashes does the normal flashes and then does the 3 green flashes then it flashes red and when i connect to pc i have 8 errors and it says i have too call naza do u think i have a broken unit?? thanks

kirikset: I'm very pleased to hear that! Trying to be helpful. There are more videos coming about in-flight tuning of NAZA and a review of FrSky telemetry system. As soon as I'm done with my exams. I hope to deliver at least 1 video before the end of June.

madebythebird: Great video, thankyou! Spent days interpreting those horrible manuals but this video explains setup very well. For noobs, it would be good to include some definitions of terms, too.

dtmpowerboss: слыш как начинать летать нада арм делать каждый раз я полностю газ выкличаю?

Саша Куприн: отличный обзор!!! А на русском такой есть?

Gareth Rens: How do you do compass calibration if you have the 3 position switch set to FS-A-M modes?

dtmpowerboss: в autopilot там есть remote adjust x1 или x2 и патом на пульте мона регулирувать у меня есть gps и у меня dx7s пульт и я когда виставляю на х1 или х2 неработает крутилка

Chris Gregory: Hi - thanks for this video. have you or do you know anyone who has successfully configured the turnigy 9x with the DJI WKM? I'm fairly new to this hobby, but I'm told that the WKM is the best in the industry and the 9x may not work - thoughts?

kirikset: You can set It up with either acro or heli mode as you wish

kirikset: Thanks! 1) may seem crazy weird but I find it the easiest to set up mode switching. I describe in the video how I use flat pitch curves to choose flight modes. Basically you can assign 3 pitch curves to 3 positions of a 3 way switc on Turnigy 9x in heli mode. To do it in plane or glider modes you have to use lots of mixes and it all gets unwieldy to adjust late. Yuou don’t have to do it if you want only 2 modes on 1 switch or have a better radio with a dedicated 3-position gyro or gear switch.

Blog Dir: Building the website was not the hard part, but monetizing it was a whole new story. Thanks for the guidance about adsense. I am finally getting some money for my business directory. This is good for both business owners and customers. Keep building quality site and everyone wins.
Rating:
How to set up DJI Naza step by step video with transmitter setup 4.9 out of 5

Shared by Others

How to set up DJI Naza step by step video with transmitter setup
How to set up DJI Naza step by step video with transmitter setup
DJI Phantom NAZA How to Install and Set up Futaba SBUS Transmitter 8FG 14SG Radio with Failsafe Mix
DJI Phantom NAZA How to Install and Set up Futaba SBUS Transmitter 8FG 14SG Radio with Failsafe Mix
DJI Naza Setup F450 Flame Wheel step by step and Transmitter Setup
DJI Naza Setup F450 Flame Wheel step by step and Transmitter Setup
How to Configure DJI Naza Control Modes (Attitude and Manual) with Turnigy 9x Transmitter
How to Configure DJI Naza Control Modes (Attitude and Manual) with Turnigy 9x Transmitter
How to Setup FPV w/ GoPro HD. HobbyKing 5.8GHz Transmitter/Receiver for DJI Naza Quadcopter
How to Setup FPV w/ GoPro HD. HobbyKing 5.8GHz Transmitter/Receiver for DJI Naza Quadcopter
DJI Phantom GoodLuckBuy Gimbal Setup Installation Tutorial
DJI Phantom GoodLuckBuy Gimbal Setup Installation Tutorial
DJI NAZA set-up with DX6i & failsafe
DJI NAZA set-up with DX6i & failsafe
Turnigy 9X FrSky Transmitter Upgrade and Binding with TBS Discovery and DJI Naza
Turnigy 9X FrSky Transmitter Upgrade and Binding with TBS Discovery and DJI Naza
ArduPilot ArduCopter APM 2.5 Configuration with Turnigy 9X Transmitter and Receiver for Quadcopter
ArduPilot ArduCopter APM 2.5 Configuration with Turnigy 9X Transmitter and Receiver for Quadcopter
DJI Naza Voltage Monitoring - First Level Voltage Protection Setup
DJI Naza Voltage Monitoring - First Level Voltage Protection Setup
DJI Naza Installation and setup New Guide -- Part 1
DJI Naza Installation and setup New Guide -- Part 1
DJI Naza Installation and setup New Guide -- Part 3
DJI Naza Installation and setup New Guide -- Part 3
FPV Team Blacksheep Discovery Quadcopter DJI Naza Review and Setup
FPV Team Blacksheep Discovery Quadcopter DJI Naza Review and Setup
DJI Naza Basic and Attitude Gain Settings for Pitch & Roll Using Turnigy 9X Control Knobs
DJI Naza Basic and Attitude Gain Settings for Pitch & Roll Using Turnigy 9X Control Knobs
DJI F550 FLAMEWHEEL NAZA HEXACOPTER  ARF  STEP BY STEP  COMPLETE BUILD
DJI F550 FLAMEWHEEL NAZA HEXACOPTER ARF STEP BY STEP COMPLETE BUILD
DJI Naza-H Assistant Software Configuration
DJI Naza-H Assistant Software Configuration
DJI Phantom or Naza V2 setup DX8 Spektrum Transmitter including bind failsafe test in 7 mins
DJI Phantom or Naza V2 setup DX8 Spektrum Transmitter including bind failsafe test in 7 mins
Phantom2 iOSD Mini FPV Transmitter & Zenmuse H3-2D install - That HPI Guy
Phantom2 iOSD Mini FPV Transmitter & Zenmuse H3-2D install - That HPI Guy
DJI Naza 3 Flight Modes (Attitude. Manual. and GPS) w/ Turnigy 9X Transmitter and 3 Position Switch
DJI Naza 3 Flight Modes (Attitude. Manual. and GPS) w/ Turnigy 9X Transmitter and 3 Position Switch
NAZA Lite and NAZA V1 GPS Mounting. Configuration. Calibration with Walkera 3 Mode Switch
NAZA Lite and NAZA V1 GPS Mounting. Configuration. Calibration with Walkera 3 Mode Switch
My DJI Phantom 2 Zenmuse H3-3D and FPV setup
My DJI Phantom 2 Zenmuse H3-3D and FPV setup
DJI F550 Flame Wheel feat. Wookong M + NAZA Video-Tutorial/ Review
DJI F550 Flame Wheel feat. Wookong M + NAZA Video-Tutorial/ Review
DJI F450 Quadcopter Drone - KK2 1 Setup. Transmitter Binding. ESC Calibration
DJI F450 Quadcopter Drone - KK2 1 Setup. Transmitter Binding. ESC Calibration
How to Set-Up Basic FPV on DJI Phantom
How to Set-Up Basic FPV on DJI Phantom
Programming your Radio to use with DJI naza M GPS - Detailed Guide
Programming your Radio to use with DJI naza M GPS - Detailed Guide
How to Use DJI Phantom 2. Vision + Plus Assistant Software. Calibration. Setup. Change to Naza M
How to Use DJI Phantom 2. Vision + Plus Assistant Software. Calibration. Setup. Change to Naza M
How to program DJI Naza M GPS - Detailed Guide
How to program DJI Naza M GPS - Detailed Guide
How to setup DJI Naza gains using Radio and DJI Assist
How to setup DJI Naza gains using Radio and DJI Assist

Featured Video

How to Make Money Online


How to set up DJI Naza step by step video with transmitter setup